![Nathan Boyce](/img/default-banner.jpg)
- 51
- 480 744
Nathan Boyce
United States
Приєднався 16 лип 2010
Hi! I’m Nathan Boyce. On my channel, you will find videos related to Automotive, metalworking, woodworking and fabrication.
www.nateboyce.com/
www.nateboyce.com/
Picking up Massey Ferguson 124 baler
In this video I pick up a Massey Ferguson 124 baler and drag it to my farm.
Переглядів: 1 589
Відео
Windshield wiper blade refill replacement
Переглядів 1864 роки тому
In this video I replace windshield wipers using refiles on a YJ jeep and Dodge L700 cab over.
Band Saw Music Box
Переглядів 2064 роки тому
I build a band saw box out of some wood in my firewood pile and add a music player.
T Slot Cleaner Build
Переглядів 7604 роки тому
I build a T Slot cleaner out of some scrap aluminum round stock for a mill drill.
Carburetor studs concentricity
Переглядів 1204 роки тому
In this video I use a case gauge to compare 3 differ brands of carb studs. Jegs, Trans-Dapt and Edelbrock.
Disc Bearing Replacement
Переглядів 12 тис.4 роки тому
In this video I replace the rear disk bearings on a WHITE disk with sealed bearings. I also replace a couple disc blades.
1969 Dodge L700 grain truck rear brake repair
Переглядів 3,7 тис.4 роки тому
In this Video I remove spoke rims,replace some axle studs and rebuild the rear break wheel cylinder in a 1969 Dodge L700 grain truck. Remove the spoke/stare rims. Remove the Eaton 2 speed rear axle shaft. Clean and rebuild drum brake wheel cylinders. Replace axle stud. Bleed the brakes with a power brake bleeder.
Copper coated claw hammer
Переглядів 1714 роки тому
In this video I copper coat a claw hammer and replace the handle.
I add a air blow off nozzle to my glass bead blast cabinet
Переглядів 1784 роки тому
In this video I add a air line and blow off nozzle to my glass bead blast cabinet to keep the glass beads off my floor. This allows me to clean the glass beads off the parts I'm blasting before removing the part.
Honda vf750 oil change
Переглядів 20 тис.5 років тому
In this video I change the oil on a 1984 Honda vf750 magna.
Reloading bench build part 2
Переглядів 9165 років тому
In this two part series I build a reloading bench out of laminated 2x4's. Part one covers the 2x4 bench top gluing, flattening it with a hand and power hand planer. Part two covers peg board, shelf's, lighting and review.
Reloading bench build part 1
Переглядів 1,7 тис.5 років тому
In this two part series I build a reloading bench out of laminated 2x4's. Part one covers the 2x4 bench top gluing, flattening it with a hand and power hand planer. Part two covers peg board, shelf's, lighting and review.
Belt Grinder Bench Build
Переглядів 1,2 тис.5 років тому
In this video I build a new bench for my belt grinder using 2x4's to make a butcher block top and 4x4's for the legs.
How to assemble pre cut 10 frame bee hive bodies
Переглядів 3,9 тис.6 років тому
How to assemble pre cut 10 frame bee hive bodies
Langstroth bee hive and what to paint
Переглядів 1,1 тис.6 років тому
Langstroth bee hive and what to paint
Cutting open K&N oil filter Dodge Cummins 6.7
Переглядів 3,7 тис.6 років тому
Cutting open K&N oil filter Dodge Cummins 6.7
Hydraulic press metal bending brake build
Переглядів 20 тис.6 років тому
Hydraulic press metal bending brake build
How to remove broken key from Trimax padlock
Переглядів 11 тис.6 років тому
How to remove broken key from Trimax padlock
Rocking chair spindle repair on the lathe
Переглядів 1,2 тис.6 років тому
Rocking chair spindle repair on the lathe
OnlineMetals Brass/Aluminium Protobox
Переглядів 4426 років тому
OnlineMetals Brass/Aluminium Protobox
How to change the oil on a John Deere 4430
Переглядів 18 тис.6 років тому
How to change the oil on a John Deere 4430
How to change John Deere 4430 fuel filters
Переглядів 38 тис.6 років тому
How to change John Deere 4430 fuel filters
Thank you very much, I think my 4430 just jelled up even with a winter blend fuel.
I somehow lost the Norris adjuster and for the longest of time could not find a replacement anywhere. The most unhelpful was actually Stanley Customer Service. This problem made the plane useless to me and I then got a veritas low angle jack . The stanley one sans the adjuster sits on a shelf reminding me that entry price is not the only driver to determine the buying decision
No Air Brakes on this one? This truck is super rare and definitely not going to find another. Is this truck still up and running for Harvest? I just now saw this video.
I sold it last year. I wish it did have air brakes.
@@nateboyce1 I saw this truck for sale a few years ago and missed the auction. Then I ran across your video last night... Wish I would have caught it before you sold it... It had a 360 V8 in it didn't it? Could you gross 50,000 with it?
@@thedesertdwellerfromutah4354 Yes it had a 360. It was missing the choke which not sure how that happened because it was a cable choke. I put a Elderbrock intake and carb on it. It ran great. Max GVW was 27,500LBS.
Is your red diesel died for on-farm use?
Yes.
Isn’t that dangerous? By soldering an o2 sensor wire together doesn’t it risk in high temperatures spreading throughout the sensor causing it to burn out what happened to the plastic connector because mine broke and am looking for a connector to replace it I was thinking of soldering as well but I’m a bit sceptic. After soldering yours did it work ok 😁
It worked but was only temporary till the new ones he ordered cam in.
Its not a handle, its a Tote. :o)
Thanks for the quick demonstration on using the Copy Crafter. I recently purchased a lathe and duplicator at two different estate sales and this allows me to understand what is involved in setting them up and using them. Funny enough, I think my first projects will be making fine handles out of old chair legs.
Thank you my man
Thank you Sir! Hope you good.
Unfortunately in general Toyota Sienna vans don't like cheap parts ask me how I know🙄🙄🙄🙄
Great stand, thanks for creating and sharing. LOL, love the smoker in the background. I used the same unit when I had bees. :)
way.. way…. way….. way…… way!! too effin long man!! u coulda edited that down to 15-20-25 seconds apart from the fact that I have never used the equipment that you have used to construct a hive box! r u launching these hives into space? get a life! You clearly have too much spare time on your hands, but I appreciate your attention to detail… I hope you gave raising your kids that much care
It happened to me too, never buy after market o2 oxygen sensors, Thank you so much 👌
Damn these trucks are fucking rare
Nice video. Short and straight to the point. Mine is a nissan b14, doesnt start in the morning. I will try this and see if it works. Thanks.
IS THIS THE SAME SETUP AS A 4440?THANK YOU!
The 4440 has the 466 which is very similar.
Well we should of gotten the end result of you putting it in the car an seeing if it work
I need more info on the 30-43LE 52104180AC These seem like older models I have a 1999 I see nothing on these numbers I got. I have a 4.0 V6 2WD
What happens if you plug ETON BLACKOUT BUDDY on 220V, 230V and 240V ? Does it smoke and pop ?
thank you for this video. just got a 4430 a month ago and want to go through a tune up with mines.
Thank you my first time went smooth !!
How much oil ? I have 1983 magna v45
?
What was the symptoms you were experiencing?
I live in tampico mexico AND a sienna 2008, get codes p0158, p0172 AND p0175. Cant find a denso O2 sensor and my firts test was on injetech replacement for toyota part number. The code was gone and will drike to see hhow IT works. Scanner reports almost the same values for fuel trim, sensor voltage and current for banks 1 and 2. Hope this replacement Brand works fine. Attach picture of box. For the two codes indicaring rich condición in both banks, the solution was a broken hose. Regards.. FC
Part number injetech NPC 41143 for sensor 2 Bank 2
Very good video, sir. I really like the way it all turned out and I would be proud to have that setup in my space when finished. 👍
Really good video, sir. I am fixing to build one myself so I appreciate the ideas and techniques. On to part 2. 👍
Can make video john deere 4430 how to clean small glass fuel filter
I just bought one of these. Do you still have yours?
I do. Used it last year for wheat harvest.
@@nateboyce1 how do I get in touch with you. Part's are going to be interesting.
@@jerrysmeltzer3016 on my channel the about tab has a email. Parts are very hard to find.
Excellent vid !!! Great instructions and demonstration !!!
I order mine today in Amazon 😃
Thanks for sharing. I just got a copy crafter with a Craftsman 12" lathe. Was wondering how effective it was and if it was worth setting up.
Hello, I'm from Antofagasta-Chile and I have a Honda Magna 750 1983. I send my bike to make oil changes. Seeing the video makes me feel like doing it once. Question: What type of filter I should put on the bike (brand, details). Once the used oil is emptied, how many liters are cast out of the new oil? Finally: what oil is thrown into the cardan (brand) and how much is it cast?? . For both jobs only used oils are emptied and changed for the new directly ?? ??, no one has to clean inside or something?? Waiting for your help. Thank you.
Do not buy spare blades not available
too late. I did this mistake.
Pre filling the filter could cause contamination.
How so?
@@nateboyce1 I retired from a Cat dealer, we were Taught by Cat to never fill a oil filter To eliminate foreign partials. We were highly doing oil sampling At each service interval. You can prefilled if you want. LOL.
Cómo se llama la herramienta?
These bloody o2 sensor issues seem to be an endemic on all Sienna. There should be a recall for it.
If it's not flat out of the box for that price send it back and get another one
What is your name ply sar
Is the ax5 tail housing the same as the ax15 tail housing ?
Memories of when i was 10y old. US farm boys started young back then. Ours didn't have a cab. Out in the elements built a man out of ya. I didn't think of it as being work then, it was fun.
I don't often see 10 wheel trucks without air brakes.
I wish it had air brakes.
Thanks. This helped me on my first fuel filter change on my 4630. The primer pump existence was the biggest help.
I have this plane and love it. Only problem is they cut some real corners, especially on the aluminum cap and the throat knob. My throat knob stripped out. Any ideas on how to reinforce this knob?
It has a limited lifetime warranty so you might try reaching out to Stanley tools.
Do u know what weight oil to use in hydrolics and trans?
The book calls for John Deere type 303
@@nateboyce1 ok. Thanks .
Cool shit
NIce!
Can anybody tell me where the ID tag is located on an AX15 in a 97 Dakota 3.9L 2wd 5 speed manual.
What if they go on the wrong way?
Could cause bearing issues.
👍
@@nateboyce1 I just took mine off and didn't mark them
Sir good intentions on your part considered I would suggest that you be more familiar with the tools and names of the parts before making a video explaining them..
my input shaft is a 10 spline but intermediate plate is aluminium but drain is on right.So you have me confused.My ID plate is gone also.My tj is a 99 4.0 from factory.What do you think it is.dont have transfer case off yet.Great video,thank you.
1999 should be a ax-15 in 2000 they went to the nv3550. The nv3550 is a aluminum case.
@@nateboyce1 my case is all aluminium.Tag is gone but the drain is on right lower side not on bottom.Comes off from passenger side for sure.Actually their are some stuff that says 1998 and some 99.So late part of year of 98 im thinking.T-case says 98.Thank you